Hik Connect User Series Magnetic Lock
DS-K1100 Series Card Readers Connect to DS-K2600 Series Access Controllers by RS-485. DS-K1100 Series Card Readers Connect toDS-K1T105&DS-K1T200 Series Access Control Terminal. DS-K4H250/450/258 series magnetic lock connect to DS-K2600 series Access Controller. DS-K4H250/450/258 series magnetic lock connect to DS-K2800 series Access Controller.
Step 3 Check Enable and a Service Terms window will pop up. Step 2 Go to System > Network > Advanced > Platform Access. Step 1 Go to System > Network > TCP/IP. Pictures, charts, images and all other information hereinafter are for description and.How to Configure Hik Connect with Gui 4.0 V4.
Hikmicro LYNX PRO-LH25 Thermal Imaging MonocularPlease take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Hikmicro LYNX PRO-LH19 Thermal Imaging Monocular Hikmicro LYNX PRO-LH15 Thermal Imaging Monocular Hikmicro LYNX-L15 Thermal Imaging Monocular Hikmicro LYNX-LC06 Thermal Imaging Monocular
However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Industry Canada ICES-003 ComplianceThis device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.1. This device must accept any interference received, including interference that may cause undesired operation. This device may not cause harmful interference.2. Operation is subject to the following two1. FCC ConditionsThis device complies with part 15 of the FCC Rules.
The high-sensitivity built-in IR detectorProvides you with clear view even in total darkness. Introduction Box ContentHandheld Thermal Monocular Camera Instruction Manual OverviewThe handheld thermal monocular is a handheld thermal camera with functions of observation, highest temperature spot mark, distance measurement, hot spot, and so on. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. This device must accept any interference, including interference that may cause undesired operation of the device.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. Operation is subject to the following two conditions: this device may not cause interference, and2.
When you connect the device to PC, the device displays images, but functions such as recording, capturing and hot spot are disabled.1. When you connect the device to PC for the first time, it installs the drive program automatically. Appearance DimensionHandheld Thermal Monocular Camera Instruction Manual Up to five hours continuous running (hot spot function off)The device can detect the distance between you and the target.The device detects and marks the spot of highest temperature.The device can capture snapshots, recordvideos, and set parameters via APP after being connected to your phone.The device can correct the defective pixels on the screen which are not performing asexpected.Built-in memory module supports video recording/snapshot capturing.Device supports 1×, 2×, and 4× digital zoom.
Hik Connect User Upgrade File And
Reboot the monocular and the device upgrades automatically. Copy the upgrade file and paste it to the root directory of the device.4. Disconnect the device from your PC Upgrade2. Select and copy the snapshots to PC and view the files.3. Select and copy the videos to PC and play the file with the player. Enter DCIM>100EZVIZ to view the videos and snapshots.
Main FunctionWhen the monocular is turned on, hold the button for three seconds to display the OSD menu.
0 kommentar(er)
